Embellish any ceramic piece by adding an Embellie!  Just use French Dimensions (see related products) or a glaze you're already using to bond Embellies to an existing ceramic piece.  This Circle Embellie bisque measures 1.45" x 1.45" x .15".  Sold individually or in case lots of 12.

Embellie Fusing — Pre-Firing:

  1. Brush any glaze onto the backside of an Embellie. Squeeze a line of French
    Dimensions around the outer perimeter of the underside of the bisque
    embellishment, but not exactly at the edge; this will help keep French
    Dimensions from rising up over the sides of embellishment when pressed
    onto ware. Apply liberally in the center areas. While French Dimensions
    glaze is wet, press embellishment onto desired area of ware, holding it for
    approximately 5 seconds until a hold is achieved. Tip: Embellies can be
    adhered to ware without the use of French Dimensions, however,
    we recommend adhering with French Dimensions for added
    strength.
    Note: You may add embellishments to ware that has already been
    glazed but has not yet been fired.
     
  2. Brush 2 to 3 coats of clear glaze over entire piece or dip in clear dipping
    glaze if an underglaze was used. Tip: While glaze must be applied over
    underglazes for the Embellies to fuse, if 3 coats of Duncan Concepts
    Underglazes are applied to the base piece and Embellie, there
    is no need to use clear glaze. If Duncan E-Z Stroke Translucent
    Underglazes or Cover-Coat Opaque Underglazes were used, and a
    matte, unglazed finish is desired, Embelllies can be adhered using
    French Dimensions without the aid of a glaze. Let dry completely.

     
  3. Make sure ware is perfectly flat on stilt and kiln shelf, as the glaze will melt
    during firing and may cause embellishment to shift if not level.
     
  4. Fire to cone 06.

    *For best results, it is recommended to fuse bisque embellishments to flat
    and horizontal bisque ware. Attaching embellishments on surfaces that are
    slanted or angled is recommended for post-firing, as glaze will melt during
    firing and cause the embellishment to slide.

Embellie Fusing — Post-Firing: 

  1. To attach an Embellie to a non-horizontal surface, decorate as desired with
    glaze or underglaze. If an underglaze was used, brush on 2-3 coats of clear
    glaze or dip in clear dipping glaze and fire the Embellie separate from the
    base piece. Stilt and fire to cone 06.
     
  2. Once fired, squeeze a line of Aleenes 7800 Adhesive around the outer
    perimeter of the underside of the bisque embellishment, but not exactly
    at the edge; this will help keep the glue from rising up over the sides of
    embellishment when pressed onto ware. Apply liberally in the center
    areas. Attach to horizontal or vertical non-food-bearing bisque ware for
    approximately 5 seconds until a hold is achieved. Let dry completely.

Write a review

Please login or register to review

Duncan 33444 Circle Embellie Bisque

  • Brand: Duncan
  • Item Code: DUNCA 33444
  • UPC: 017754334442
  • Availability: 36
  • $1.35
  • Special $0.70 (save 48%)



Related Products

Square Embellie bisque

Duncan 33440 Square Embellie Bisque

DUNCA 33440

$0.70 $1.35

Heart Embellie bisque

Duncan 33442 Heart Embellie Bisque

DUNCA 33442

$0.70 $1.35

Star Embellie bisque

Duncan 33445 Star Embellie Bisque

DUNCA 33445

$0.70 $1.35